BaBylissPRO - Outliner Clippers

BaByliss PRO SkeletonFX GoldFX is a contour trimmer from the 4Artists line, with an all-metal gold casing and a 40 mm DLC/Titanium T-blade. The blade is exposed at 360°, so you can see the line from any hand position. It is for hairdressers and for those who trim their own contours and beards at home.

What it does for you

• See exactly where you cut: no casing covers the blade, so the line at the neck or beard remains visible.
• Cut cleanly and close to the skin, with the DLC/Titanium blade adjustable to zero-gap with the included tool.
• The blade stays cooler: the brand says that the exposed blade does not retain heat, and the DLC/Titanium layer works at a lower temperature.
• About 120 minutes cordless after 3 hours of charging, and when it runs out of battery you can work with a cord.
• Constant speed, with the digital EDM Technology motor at 7200 blade movements per minute.

How to use it at home

1. Before the first use, charge it for 3 hours uninterrupted. Maximum capacity appears after 3 charge and discharge cycles.
2. With the switch on 0, put a drop of the included oil on the blades and wipe off the excess.
3. Charging: connect the plug to the base of the machine and the adapter to the outlet. The LED flashes, and when it stays continuously lit, the battery is full.
4. Turn it on, then trace the line with the corner of the blade, in short movements, on dry and combed hair.
5. After use, clean the wires with the brush, put a few drops of oil and mount the blade protection cap.

For what type of work

It is suitable for contours at the neck and temples, the beard line, details around the ears, hair tattoos and fine lines. It does not have guide combs and is not made for shortening hair on the head; for that you use a hair clipper.

Specifications

What else you need

• BaByliss PRO 4 in 1 spray for daily blade cleaning
• Wahl oil for blades
• FX707ZE replacement blade, 40 mm T-blade
• Titanium T-blade with 2.0 mm deep tooth FX707G2ZE
• FX7870GBPBASE charging station for SkeletonFX
• Wahl haircutting cape

ProBeauty tip. When you redo the zero-gap, leave the black blade teeth 0.5–1 mm below the edge of the gold blade, as shown in the manual. Test on a small area of skin before the full contour.

The BaByliss PRO SkeletonFX Gunsteel is an edger from the 4Artists line, with a 40 mm Japanese steel T-blade exposed along its entire length. See exactly where you cut from any angle, so hairline, beard, and hair designs come out clean. It works corded or cordless and comes with a charging stand.

What it does for you

• See the line you cut: the T-blade is exposed 360°, without a housing that blocks your view.
• Cut very close to the skin, because the blade adjusts to zero-gap with an included tool, without having to disassemble it.
• Work for about 120 minutes cordlessly after 3 hours of charging. A quick 30-minute charge gives you about 30 minutes of work.
• Always know how much you have left: the red LED flashes when there are approximately 10 minutes of battery life left.
• Keeps up with thick hair, with the EDM Technology digital motor at 7200 blade movements per minute.

How to use it at home

1. Before first use, charge it continuously for 3 hours. The battery reaches maximum capacity after 3 full charge and discharge cycles.
2. With the switch on 0, put a drop of oil on the blades and wipe off the excess with a dry cloth.
3. Work on dry and combed hair. For straight lines at the neck and temples, gently support the corner of the blade on the skin.
4. Around the ear and on the beard line, make short passes and check the line from the side after each pass.
5. At the end, remove the hair with the included brush and put a few drops of oil on the blades.
6. Place it in the stand with the switch on 0, so it charges.

For what type of work

It is designed for finishing: the hairline and temples, the beard line, the edges around the ears, designs and fine lines in short hair. It does not have guide combs, so you do not cut all your hair with it; for that you need a hair clipper.

Specifications

What else you need

• BaByliss PRO 4-in-1 spray for cleaning and cooling the blades
• Wahl oil for hair clipper blades
• Titanium T-Blade with 2.0 mm deep tooth FX707C2ZE, for FX7870
• Carbon finishing comb
• Wahl cutting cape

ProBeauty tip. The manual limits direct plug-in use to 20 minutes. If the battery ran out in the middle of an edging, put the machine in the stand for 30 minutes: it gives you about 30 minutes of work.

BaByliss PRO FXONE Skeleton Black is a contour trimmer with an all-black metal body, a 360° exposed T-blade with standard teeth in Blue Titanium, and an interchangeable FXONE battery. It is designed for clean lines, contours, and detailing.

Resealed product. It has been unsealed for inspection or display and may show minor signs of wear or handling. It is complete and fully functional, tested by us, and comes with the same warranty as a new product. It does not include the original box.

What it does for you

• See the line as you cut, thanks to the fully exposed T-blade, which can be adjusted to a zero-gap setting.
• The blade is durable and heats up less: the brand describes it as Blue Titanium, offering high resistance and a lower operating temperature.
• Work for up to 3 hours after a 2-hour charge, with a battery that can be changed with the push of a button.
• Consistent performance from the high-torque, brushless digital motor operating at 7200 RPM.
• Easy cleaning: the hair compartment cover is removable.

How to use it at home

1. Place the battery on the included charging base and monitor the 4-stage LED ring.
2. Lubricate the blade with a few drops of oil before use.
3. For a closer cut, use the included tool and screwdriver to adjust the zero-gap setting.
4. Outline the area on dry, combed hair using short strokes, and check the line from the side.
5. After use, remove the hair compartment cover, clean it with the brush, lubricate the blade, and attach the blade guard.

What it is designed for

It is designed for outlining the neck and temples, defining the beard line, creating hard lines, and fine detailing. The blade's standard teeth make it suitable for most skin types. It does not include guide combs, so it is not the right machine for cutting hair all over the head.

Specifications

What else you may need

• BaByliss PRO 4-in-1 Blade Spray
• Wahl Blade Oil
• FXONE FXBB33E Spare Battery
• FXONE All-Metal Trimmer, Same Battery
• Carbon Finishing Comb

ProBeauty Tip. If you already have an FXONE trimmer, keep one battery charged on the base: you can switch it between the trimmer and contour trimmer without waiting for it to charge.

Attention! The product may have an opened or damaged packaging and may show minor signs of use or small scratches that do not affect its functionality!

BaByliss PRO Skeleton FX Gold Trimmer 4artists - Precision and Professional Performance

Transform your trimming and outlining routine with Babyliss Pro SKELETON FXONE, a revolutionary trimmer designed for both professionals and personal use. Thanks to its innovative design and cutting-edge technology, this device is the ideal solution for impeccable outlines and precise details.

Advanced Technology for Exceptional Results

Babyliss Pro SKELETON FXONE comes with top-tier functionalities that make it essential for any professional toolkit:

• Revolutionary interchangeable battery system: Uses lithium-ion technology for up to 3 hours of autonomy, with a fast charging time of just 2 hours. The system allows for uninterrupted use, offering maximum freedom and efficiency.

• High-performance High Torque digital motor: With an impressive speed of 7,200 RPM, the brushless motor ensures fast and precise cutting, regardless of hair texture.

• Fully exposed T Gold Titanium blade: Perfectly adjustable for zero-gap, this blade offers full 360° visibility and excellent performance for fine details, hard lines, and clear outlines.

Premium Design and Superior Ergonomics

The SKELETON FXONE trimmer combines performance with a sleek and comfortable design:

• Improved metallic casing: Durable and sophisticated design for intensive use.
• Ergonomic handle with barbell metal grip: Provides excellent control and effortless maneuverability.
• Tapered end with hidden hook: Ideal for easy storage and quick access.

Complete Set of Included Accessories

Babyliss Pro SKELETON FXONE comes with all the accessories you need for a perfect outline:

• Dual-voltage charging base.
• Zero-gap adjustment tools for extreme precision.
• Cleaning brush and lubricating oil for device maintenance.
• Blade protection cap, spare blade cushion, and screwdriver.

Versatility and Compatibility

This trimmer is part of the FXONE range and is fully compatible with other top tools:

• Hair Clipper – for complete cutting performance.
• Shaver – for smooth finishes and perfect shaves.
  All these tools work with the same innovative interchangeable battery system.

Why Choose Babyliss Pro SKELETON FXONE?

✔ A must-have for hairstylists and personal grooming enthusiasts.
✔ Absolute precision for clear details and outlines.
✔ Ergonomic design and premium materials for comfort and durability.
✔ Consistent performance, regardless of hair type.

Elevate Your Personal Grooming Standards!

Whether you are a professional hairstylist or want to maintain your look at home, the Babyliss Pro SKELETON FXONE is the perfect choice. Enjoy total control, precision, and premium style.

Buy now and define your style at the highest level!

The BaByliss PRO Boost+ SkeletonFX Gold is a contour trimmer with a gold metal housing and a 40 mm T DLC blade, with a 2.0 mm deep tooth, exposed at 360°. It works corded or cordless.

Resealed product. It was unsealed for inspection or display and may have minor signs of wear or handling. It is complete and functional, checked by us, and has the same warranty as a new product. It comes without the original box.

What it does for you

• Sharp lines: the 2.0 mm deep tooth is recommended by the brand for very clean edges and thick hair.
• Low friction on the skin, thanks to the wear-resistant DLC coating.
• The blade remains visible in any position, and the zero-gap is achieved without removing it.
• Circa 180 minutes cordless, with the 3300 mAh lithium-ion battery, charged in 4 hours.
• Non-slip handle, covered with diamond-textured rubber.

How to use it at home

1. Charge it continuously for 4 hours before first use. Maximum capacity is reached after 4 cycles.
2. With the switch set to 0, put a drop of oil on the blades and wipe off the excess.
3. Connect the plug to the base of the machine and the adapter to the outlet; the LED flashes during charging and stays lit when it is ready.
4. Outline on dry hair, with the corner of the blade, in short strokes.
5. At the end, clean the hair with the brush, oil the blade, and set the switch to 0.

For what type of work

For contouring, the beard line, neck, temples, and hard lines, especially on thick or coarse hair. On sensitive skin, a blade with a standard tooth is gentler. It does not have guide combs and does not replace the hair clipper.

Specifications

What else you need

• BaByliss PRO 4-in-1 Blade Spray
• Wahl Blade Oil
• Replacement DLC 2.0 FX707BD2E Blade, 40 mm
• Boost+ Gold SkeletonFX FX7870GBPBASE Charging Stand
• Boost+ Gold Clipper

ProBeauty Tip. After zero-gap adjustment, check the blade on the back of your hand before the first contour. If it scratches, the moving blade protrudes too much: readjust it.

BaByliss PRO FXONE Lo-Pro is an outlining clipper with a metal blade head featuring a very low profile and a 40 mm Blue Titanium T-blade, exposed on 360°. It is part of the FXONE system, with a battery interchangeable with the Lo-Pro hair clipper. It is for clean edges, hard lines, and detailing.

What it does for you

• See the line from any angle, with the fully exposed T-blade, zero-gap adjustable.
• Gentle and durable blade: Blue Titanium, described by the brand as hypoallergenic, with a lower operating temperature.
• Constant rhythm, with the high-torque, brushless digital motor, at 6800 RPM.
• Up to 3 hours of runtime after 2 hours of charging; the battery is changed with a button.
• Fits well in the hand, thanks to the very low-profile blade head and the ergonomic handle.

How to use it at home

1. Charge the battery on the included base and check the level on the 4-step LED ring.
2. Put a few drops of oil on the blade before use.
3. If you want a closer cut to the skin, adjust the zero-gap with the included tool and screwdriver.
4. Outline on dry hair, with the corner of the blade, in short movements.
5. After use, clean the hair with the brush, lubricate the blade, and put on the blade guard.

For what type of work

It is for outlining the neck and temples, the beard line, hard lines, and fine details. The standard tooth of the blade works on most skin types. It does not have guide combs, so for shortening hair you use the FXONE Lo-Pro hair clipper.

Specifications

What else you need

• BaByliss PRO 4-in-1 spray for blades
• Wahl oil for blades
• FXONE FXBB33E spare battery
• FXONE Lo-Pro hair clipper, the same battery
• Carbon finishing comb

ProBeauty tip. For straight lines on the neck, lightly support the little finger of the neck and move only the wrist. The hand remains stable, and the line does not get crooked.

The BaByliss PRO Boost+ SkeletonFX Chameleon is a metal-bodied outline trimmer with an iridescent finish and a 40 mm titanium T-blade with a 2.0 mm deep tooth. The blade is exposed 360°, so you can see the line from any position. It works corded or cordless.

What it does for you

• Very clean edges: the 2.0 mm deep tooth is designed for hard lines and sharp contours.
• Durable blade that stays sharp: titanium is hard and, according to the brand, hypoallergenic.
• See the blade at all times, and the zero-gap can be adjusted without removing it.
• Approximately 180 minutes cordless, with a 3300 mAh battery, charged in 4 hours.
• Secure grip, with a handle covered in diamond-textured rubber.

How to use it at home

1. Before first use, charge it for 4 hours. Maximum capacity is achieved after 4 charge and discharge cycles.
2. With the switch set to 0, put a drop of oil on the blades and wipe off the excess.
3. To charge, connect the plug to the base of the machine; the LED flashes, then stays lit when it is ready.
4. Trace the outline on dry hair, with the corner of the blade, in short strokes.
5. After use, clean with the brush, oil the blade and set the switch to 0.

For what type of work

It is for contours, the beard line, neck, temples and hard lines, especially on thick or coarse hair. If your skin is easily irritated, test it on a small area first: the deep tooth cuts more aggressively. It does not replace the hair clipper.

Specifications

What else you need

• BaByliss PRO 4-in-1 blade spray
• Wahl blade oil
• Titanium 2.0 FX707C2ZE replacement blade, 40 mm
• FX7870GBPBASE charging stand for SkeletonFX
• Boost+ Chameleon hair clipper
• Carbon finishing comb

ProBeauty tip. If you do not use it often, recharge it for 4 hours approximately every 6 months, as the manual requires. The 3300 mAh battery retains its capacity this way.

BaByliss PRO FreshFX is a 167 g cordless outline trimmer with a fully exposed 40 mm Japanese steel T-blade. The DC motor runs at 6800 RPM, and the blade is zero-gap adjustable for cutting very close to the skin. The brand makes it for all experience levels.

What it does for you

• See the line you cut, because the T-blade is fully exposed.
• Close-to-skin cut, with zero-gap adjustment made with the included kit and screwdriver.
• Clean lines, with the standard 1.6 mm tooth and over a million cutting strokes per minute.
• Relaxed hand: it weighs only 167 g and has a non-slip handle, with finger and thumb support.
• Up to 90 minutes cordless, and 20 minutes of charging gives you 20 minutes of work.

How to use it at home

1. Charge it via the USB-C port on the base. The LED flashes while charging and stays lit when it's ready.
2. Put a drop of oil on the face and sides of the moving blade and wipe off the excess with a soft cloth.
3. For zero-gap, loosen the screws, push the moving blade with the tool until it reaches the level of the fixed blade or slightly below it, then tighten them.
4. Trace the outline on dry hair, with the corner of the blade, in short strokes.
5. At the end, clean the hair with the brush, oil the blade and put on the cap.

For what type of work

It is for outlines, shapes and details: neck, temples, beard line, fine lines. It is a good choice if you are just learning to outline at home. Do not cut the hair all over the head; for that you use the FreshFX clipper.

Specifications

What else you need

• BaByliss PRO 4 in 1 blade spray
• Wahl blade oil
• FreshFX FX86E clipper
• Carbon finishing comb
• Wahl cutting cape

ProBeauty tip. After zero-gap adjustment, pass the blade once lightly over the back of the hand. If you feel a scratch, the moving blade is sticking out over the fixed one and needs to be adjusted again.

The BaByliss PRO FXONE Skeleton is an outline trimmer with an all-metal body, available in gold or black, and a 360° exposed T-shaped titanium blade with a standard tooth. The battery is interchangeable and compatible with other FXONE devices. It is designed for clean edges, sharp lines, and detailing.

What it does for you

• See exactly where you cut: the T-blade is fully exposed and zero-gap adjustable.
• Durable blade that stays cooler: Gold Titanium in the gold version, Blue Titanium in the black version.
• Clean edges even in thick hair, with a high-torque, brushless digital motor running at 7200 RPM.
• Up to 3 hours of runtime after 2 hours of charging; the battery is released with a button.
• Quick cleaning, as the hair compartment cover is removable.
• Secure grip, with a textured metal handle and finger support.

How to use it at home

1. Charge the battery on the included charging base and monitor the 4-stage LED ring.
2. Lubricate the blade with a few drops of oil before use.
3. For cutting very close to the skin, adjust the zero-gap setting with the included tool and screwdriver.
4. Outline the shape on dry, combed hair using short strokes, and check the symmetry in the mirror.
5. Finally, remove the hair compartment cover, clean it with the brush, lubricate the blade, and attach the guard.

What it is designed for

It is for outlining the neck and temples, the hairline, the beard line, and detailing. The standard tooth works on most skin types. It does not include guide combs, so it does not replace a hair clipper.

Specifications

What else you need

• BaByliss PRO 4-in-1 blade spray
• Wahl blade oil
• FXONE FXBB33E spare battery
• FXONE All-Metal hair clipper, same battery
• FXONE Double Foil shaver, same battery
• Carbon finishing comb

ProBeauty tip. If you also use the FXONE hair clipper, mark the batteries with a dot of color. You will always know which one is charged and which one is on the charging base.