Spare Parts

The Wahl Senior Cordless Tension Spring 08504-7050 is the replacement tension spring for the Wahl 5 Star Senior Cordless hair clipper. The tension spring keeps the moving blade pressed against the fixed blade so that hair is cut, not pulled. When it weakens, you replace it and your clipper cuts cleanly again.

What it does for you

• Clean cutting again: a new spring restores the pressure between the blades, so the clipper no longer pulls the hair.
• You don't have to replace the whole clipper: the spring is a small and inexpensive part, and Wahl sells it as a separate replacement part for the Cordless Senior.
• Part by model code: 08504 is the code for the Senior Cordless in the Wahl model list for Europe.
• The blade wears more evenly when the blades stay close together with the correct pressure.

How to use it at home

1. Turn off the clipper and remove it from the charger.
2. Carefully disassemble the blade and note the position of the old spring before removing it.
3. Install the new spring in the same position, then put the blade back in place and align the blades.
4. Apply oil to the blade, turn on the clipper and check that it runs smoothly, without overheating.
5. If you have never disassembled a clipper before, leave the installation to an authorized Wahl service center.

For what type of device

For the Wahl Senior Cordless hair clipper (model code 08504). There is no confirmation that it fits the Senior 2.0, corded Senior, or other 5 Star models. If you have another device, write us the code on the label and we will check before ordering.

What else you need

• Wahl Senior Cordless hair clipper
• Wahl Senior Cordless 08504-7000 case
• Wahl blade oil
• Wahl Blade Ice spray for blades

ProBeauty tip. Before replacing the spring, rule out simple causes. Clean the blade of hair, apply oil and try again. If the clipper still pulls the hair, the spring or the blade needs to be replaced.

The BaByliss PRO Rotating 800 Replacement Round Brush 13827701 is the 50 mm head for the Rotating 800 rotating brush. Use it when the old brush has worn out, become deformed, or been lost. It restores your device’s ability to create volume when brushing long hair without having to buy a new device.

What it does for you

• Replace only the worn part, not the entire device.
• Volume brushing for long hair: the 50 mm head is the brand’s recommended size for longer lengths.
• Grips the hair well, with boar and nylon bristles and epoxy tips.
• Ceramic technology on the brush tube, just like the original head that comes in the box.
• Easy to clean: the brush head can be rinsed under water.

How to use it at home

1. Turn off the Rotating 800, unplug it, and let it cool down.
2. Unlock the old head using the button on the brush and gently pull it off the device body.
3. Slide the new brush onto the device body.
4. Lock it in place using the button on the top of the brush.
5. Check that it is securely attached before turning on the rotation.

For which type of device

It is for the BaByliss PRO Rotating 800, BAB2770E rotating brush. It is not a hand brush and is not compatible with the Air Styler or other hot air brushes. If you need a head for bangs and short layers, that is the 40 mm one.

Specifications

What else you need

• BaByliss PRO Rotating 800 rotating brush, the compatible device
• L’Oréal Tecni.Art Flex Blowdry leave-in cream, with heat protection
• Wella EIMI Thermal Image heat protection spray
• Hair sectioning clips

ProBeauty tip. When brushes start to bend or no longer grip the hair well, it is time to replace the head. A worn brush makes you go over the same section of hair multiple times, exposing it to more heat.

Thuya Neon UV 9W – Performance and Durability for Your UV Lamp

Thuya Neon UV 9W is the ideal choice for replacing bulbs in UV lamps, ensuring efficient and rapid curing of gels and semi-permanent polishes. With an extended lifespan and consistent performance, this product is essential for maintaining professional manicure results.

Why use Thuya Neon UV 9W

This high-quality UV neon guarantees optimal curing and long-lasting durability. It is specially designed for use with UV lamps and helps maintain their long-term efficiency, with the recommendation to change the neons every 6 months.

Key Benefits

• Extended lifespan for prolonged use
• Suitable for all compatible 9W UV lamps
• Ensures fast and even curing of gels and semi-permanent polishes
• Recommended for periodic maintenance of UV lamps
• Easy to replace, saving time and effort

Key Ingredients

• High-quality neon tubes for consistent performance
• Durable components for extended lifespan
• Efficient design for uniform UV light distribution

How to Use

• Turn off the UV lamp and unplug it from the power source before replacing the bulb
• Carefully remove the old bulb and replace it with Thuya Neon UV 9W
• Ensure the neon is correctly secured before plugging the lamp back in
• Turn on the UV lamp and check its functionality for optimal curing

With Thuya Neon UV 9W, ensure your UV lamp operates at maximum performance and delivers professional manicure services every day!

BaByliss PRO FX8700GBASE is a charging base for metal FX clippers with a hanging ring: ChameleonFX FX8700IE, RedFX FX8700RE, and BlackFX FX8700BKE. The brand designed it for barbers who don't hang up their clippers. It keeps the clipper upright on the counter and charges it using the adapter supplied with the clipper.

What it does for you

• The clipper no longer falls off the counter: the base is solid, balanced, and stable.
• It stands upright and securely while charging.
• You charge it easily, without hanging it or leaving it lying down next to the cable.
• Your clipper is always charged and within reach at your workstation.

How to use it at home

1. Check the list below to make sure your clipper is a compatible model.
2. Place the base on a flat, stable surface near an outlet.
3. Connect the adapter supplied with the clipper, then plug it in.
4. Place the clipper in the base, upright, and check that it stands securely.
5. When moving the base, first unplug the adapter.

For what type of device

BaByliss PRO lists it as compatible only with the FX clippers with a hanging ring: ChameleonFX FX8700IE, RedFX FX8700RE, and BlackFX FX8700BKE. The GoldFX FX8700GE clipper and Boost+ clippers are not listed by the brand; separate bases are available for the Boost+. It is not designed for edgers.

Specifications

What else you need

• BaByliss PRO FXPCGE 8-piece guard set for FX8700
• BaByliss PRO FX4in1 blade maintenance spray
• Wahl clipper blade oil
• BaByliss PRO M3969E magnetic mat for your workstation

ProBeauty tip. Before ordering, check the code on your clipper's label: the base is listed only for FX8700IE, FX8700RE, and FX8700BKE. If you have a different FX8700 clipper, look for the base designed for it.

The Wahl Beret Stealth and Beretto Charger 97581-2016 is the mains power supply that Wahl lists in the official parts list for Beret and Beretto machines. Get it if you have lost or damaged the original power supply. Your clipper will be back in action without having to buy another device.

What it does for you

• Gets your machine running again: charge the Beret's lithium-ion battery with the original part, not with a random adapter.
• You know you have the correct code: 97581-2016 appears in the Wahl parts list as the transformer for Beret and Beretto.
• One power supply for two devices: if you have both Beret and Beretto, the same part is listed for both.
• Fast charging: Wahl gives the Beret 60 minutes of charging for 75 minutes of use.

How to use it at home

1. Check the old power supply or the parts list: the code should be 97581-2016.
2. Connect the plug to the charging stand or the machine, exactly as the original power supply was connected.
3. Plug the power supply into the wall and let the machine charge fully before the first use.
4. After charging, unplug the power supply and keep it dry, away from water.

For which type of device

For Wahl Beret (08841-616 and the black Stealth Beret version, 08841-1516) and Wahl Beretto (4212-0470) clippers, as grouped in the Wahl parts list. It is not a universal charger: for Magic Clip, Senior, or other models, you should look for their respective power supplies. If you have an older Beret with a different code on the label, ask us before ordering.

Specifications

What else you need

• Wahl Beret Clipper
• Wahl Beret Stealth Replacement Blade
• Wahl Blade Oil
• Wahl Blade Ice Spray for Blades

ProBeauty Tip. If the machine no longer charges, first check the contacts on the stand and the machine. Clean them with a dry brush; sometimes hair buildup there stops the charging, not the power supply.

The Wahl Detailer Motor 08723-1401 is the replacement motor listed in the official Wahl parts list for corded Detailer and Wide Detailer trimmers. Replace it when the old motor has failed but the rest of the trimmer is in good condition. The Detailer is part of the Wahl 5 Star series.

What it does for you

• Save the trimmer: replace the motor, not the entire device.
• One motor for two models: the Wahl parts list identifies it as the "Detailer / Wide Detailer Motor".
• Original Wahl part, with a code from the brand's parts list.
• The trimmer works like new again: the motor is the original model motor, not an adapted one.

How to use it at home

1. Unplug the trimmer and first check the cable and blade, which wear out more often than the motor.
2. Confirm the model on the label: corded Detailer or Wide Detailer.
3. Take the trimmer and motor to an authorized Wahl service center for installation.
4. After repair, oil the blade and test the trimmer before the first client.

For which type of device

For corded Wahl trimmers: Detailer (08081-016) and Wide Detailer, as listed in the Wahl parts list. It is not for the Cordless Detailer Li, Hi-Viz, or Beret. If you do not know which model you have, send us the code from the label.

What else you need

• Corded Wahl Wide Detailer Trimmer
• Wahl Detailer T-Wide Replacement Blade
• Wahl Blade Oil
• Wahl Blade Ice Spray

ProBeauty Tip. On corded trimmers, a twisted or bent cable at the base can cause the same symptoms as a faulty motor. Check it first; you may not need a new motor.

The Moser Genio Plus Removable Battery 1854-7988 is the spare battery Moser provides for the Genio Plus clipper. The Genio Plus comes with two interchangeable batteries: one is in use while the other charges on the charging stand. With an extra battery or a replacement for a worn-out one, your clipper is always ready to work.

What it does for you

• Shave without charging breaks: remove the empty battery and insert a fully charged one in a few seconds.
• Real runtime: Moser provides approximately 100 minutes of shaving time on a full charge.
• Fast charging: approximately 75 minutes to a full charge on the clipper's charging stand.
• Original NiMH battery: the manual requires only the original battery, which features thermal protection.

How to use it at home

1. For the first use, charge the battery for 1.5 hours, as required by the Genio Plus manual.
2. Press the release buttons on the side and remove the old battery from the clipper.
3. Place the battery on the charging stand; the red LED lights up and flashes when charging is complete.
4. Push the charged battery into the clipper until you hear it click into place.
5. Recharge only when the indicator light on the clipper turns on; at that point, you have about 15% battery life remaining.

For which type of device

For the Moser Genio Plus clipper and, according to the Moser parts list, the Moser Arco 1854-0081 pet clipper. It is not for the standard Genio, model 1565, which has an internal battery.

Specifications

What else you need

• Moser Genio Plus Motor 1854-7060
• Moser Support and Guide 1854-7833
• Blade oil
• Blade cooling and cleaning spray

ProBeauty tip. Always leave the second battery on the charging stand. This way, you'll have a fully charged one ready when the battery in the clipper runs out, and both will wear evenly.

The Wahl Cordless Senior Set housing 08504-7065 is the housing set for the Wahl Cordless Senior clipper. Use it when your clipper's housing is cracked, broken, or heavily scratched. The photo shows the black top cover with the Senior cordless inscription, the silver lower housing, with a gold lever, and the small mounting parts.

What it does for you

• Repair the clipper, don't replace it, when the only problem is the housing.
• Black top cover, with the Wahl inscription, the five stars, and Senior cordless.
• Silver lower housing, with the gold adjustment lever mounted.
• Small mounting parts: a metal spring, a washer, and three screws, as seen in the photo.

How to use it at home

1. First, check your clipper's code and model on the label under the housing or in the manual.
2. Unplug the clipper and remove it from the charging stand.
3. Take a photo of the clipper before you disassemble it, so you know where each part goes.
4. Move the internal components into the new housing and tighten the screws without forcing them.
5. If you have never disassembled a clipper before, leave the assembly to a service center.

For what type of clipper

For the Wahl Cordless Senior clipper, the model written on the cover. Wahl has made several generations of the Senior, corded or cordless, so check the model before ordering. If you are not sure, write us the code on your clipper and we will confirm the compatibility.

Specifications

What else you need

• Wahl 5 Star Cordless Senior Clipper
• Wahl Blade Oil
• Wahl Blade Ice Spray for cooling the blades

ProBeauty Tip. While you have the clipper disassembled, clean out all the hair trapped inside with a dry brush and put a drop of oil on the blade. On a new housing, a clean clipper works and sounds like new.

The Moser Primat 1230 1230-7035 lever pivot set is the set of pivots listed in the official Moser parts list for the Primat 1230 hair clipper. The pivots hold the mechanism lever in place. Replace them when the lever has play, squeaks, or the clipper starts cutting unevenly.

What it does for you

• The mechanism runs tightly again: new pivots remove the play in the lever.
• The clipper runs quietly: Moser describes the Primat as very quiet, and loose parts make noise.
• Part by Moser code: 1230-7035 is listed in the parts list for the Primat 1230 model.
• Inexpensive repair: you replace a few small pivots, not the whole clipper.

How to use it at home

1. Unplug the clipper and open the blade and housing.
2. Take a photo of the lever and pivots before removing anything.
3. Replace the old pivots with the new ones in the same position.
4. Close the clipper, oil the blade, and run a short test.
5. If you have never worked on the mechanism of a clipper, leave the assembly to an authorized service center.

For what type of device

For the Moser Primat 1230 corded hair clipper, as listed in the Moser parts list. We have no confirmation for the Primat 2in1 or other models.

Specifications

What else you need

• Moser Primat 1230-7730 balancer
• Moser Primat 1230-7472 blade support
• Moser Primat 1230-7720 blade guide
• Moser Primat 1230-7071 switch
• Blade oil
• Blade cooling and cleaning spray

ProBeauty tip. If you are taking apart the mechanism anyway, also check the balancer and the guide. The parts around the lever wear out together; replace them all at once and you won't have to take the clipper apart again anytime soon.

The Moser Primat 1230 Blade Support and 1230-7472 adjustment segment is a replacement part for the blade area of the Moser Primat corded hair clipper. Primat is a Moser model, and the 1230 codes are its parts in the official parts list. Moser does not publish a data sheet for code 1230-7472, so you order it when the code on the old part or the service center tells you exactly this code.

What it does for you

• The blade is securely fixed again: a broken or worn blade support makes the blade loose.
• Straight cutting line: with the blade properly seated, the cut is uniform.
• Order by code: compare 1230-7472 with the code on the old part before installation.
• You don't replace the whole machine: Primat is designed for continuous work and is worth repairing.

How to use it at home

1. Unplug the machine and open the blade.
2. Take a photo of how the old part is positioned and compare its code and shape with the new part.
3. Mount the new support in the same position, then put the blade back in place.
4. Check the cutting length adjustment in all positions, lubricate the blade and turn on the machine as a test.
5. If you have never opened a machine before, leave the installation to an authorized service center.

For what type of device

For the Moser Primat 1230 corded hair clipper. For Primat 2in1 or other models we have no confirmation; check the type on the machine's label.

What else you need

• Guide for Moser Primat 1230-7720 blade
• Moser Primat 1230-7035 pivot set
• Moser Primat 1230-7730 balancer
• Moser Primat 1230-7590 upper housing
• Blade oil
• Cooling and cleaning spray for blades

ProBeauty's tip. When you replace a part in the blade area, also check the blade. If it is worn or has broken teeth, replace it then too; otherwise, the new part will wear out quickly.

The BaByliss PRO Boost+ Chameleon FX8700IBPBASE Charging Stand is the charging stand for the Boost+ Chameleon hair clipper. It is compatible with all FX8700 series hair clippers that have a hanging hook. The clipper stands vertically on the stand and charges via its adapter, which is not included.

What it does for you

• The clipper stands upright and does not tip over, because the stand is solid, balanced, and stable.
• Effortless charging: place the clipper on the stand and charging begins.
• Use the adapter you already have from the hair clipper.
• Use it with the entire FX8700 series with a hook, not just the Chameleon model.
• Your workspace stays tidy, with the clipper always in the same place.

How to use it at home

1. Place the stand on a flat, dry, and stable surface, near an electrical outlet.
2. Connect the hair clipper adapter to the stand, then plug the adapter into the outlet.
3. Place the clipper in the stand in a vertical position, and check that it is secure.
4. Wipe the hair off the clipper before placing it on charge.
5. When moving the stand, first remove the adapter from the outlet.

For what type of device

BaByliss PRO recommends it for the Boost+ professional hair clipper and all FX8700 hair clippers with a hanging hook. It is not made for FX7870 trimmers, which have their own stand. Without the clipper adapter, the stand does not charge.

Specifications

What else you need

• BaByliss PRO Boost+ Chameleon hair clipper, for which the stand is designed
• BaByliss PRO FXPCGE 8-piece guard set for FX8700
• BaByliss PRO FX4in1 spray for blade maintenance
• Wahl oil for hair clipper blades

ProBeauty tip. If you have two FX8700 clippers on standby, place each on its stand and use a single adapter for the one you use more often. This way, you always know which clipper is charged.

The Wahl 5 Star Vanish Replacement Battery 08173-7030 is the replacement battery for the Wahl 5 Star Vanish shaver. The Vanish uses a lithium-ion battery, and Wahl clearly states that you should not remove it yourself. It should be installed by an authorized service center.

What it does for you

• The shaver works cordlessly again after the service center replaces the worn-out battery.
• Don't throw away the shaver: you only replace the battery, not the entire Vanish.
• Part with the Vanish family code, for the 08173-716 shaver.
• You know what to expect: Wahl gives the Vanish 100 minutes of use on a 50-minute charge.

How to use it at home

1. Fully charge the Vanish. When it's full, all 3 LEDs remain lit.
2. Use it cordlessly and monitor how long it lasts. When the battery is almost empty, the LEDs flash.
3. If it discharges much faster than 100 minutes, first check the power supply and contacts.
4. Until it is repaired, you can use the shaver while it is connected to the cable.
5. Take the entire shaver, along with the new battery, to an authorized Wahl service center. Do not remove the old battery yourself.

For what type of shaver

It is for the Wahl 5 Star Vanish shaver, code 08173-716. Compatibility is confirmed only for the Vanish, so do not buy it for other Wahl shavers. The old battery should not be disposed of with household waste; hand it in at a collection point.

Specifications

What else you need

• The Wahl 5 Star Vanish shaver, for which this part is intended
• Replacement motor for the Wahl Vanish
• Wahl Power Station charging station, compatible with the Vanish
• Wahl 3022905 replacement foil and blades for the Vanish

ProBeauty tip. Lithium-ion batteries do not like cold or heat. Wahl requires that you do not store or charge the shaver below 0 °C or above 45 °C, so do not leave it in the car during winter.

The Wahl 5 Star Vanish replacement motor 08173-7010 is the replacement part for the motor of the Wahl 5 Star Vanish shaver. It is a service part: it is installed by an authorized workshop or a qualified technician, not by you at home. You only need it if the shaver's motor has failed.

What it does for you

• Repair the Vanish instead of replacing it, when the motor no longer works.
• Part with the Vanish family code, for the 08173-716 shaver.
• Take it to the service center along with the shaver, so the repair doesn't have to wait for the part.
• Find out first if it really is the motor: the steps below help you rule out simple causes.

How to use it at home

1. Check the socket with another device that you know for sure works.
2. Check that the socket is not one that turns off with the room light.
3. Clean the shaver's contacts and the power supply of hair and dirt.
4. If the shaver only runs slower and the foil heats up, first replace the foil and blades. This is normal wear and tear, not the motor.
5. If it still doesn't start, take the shaver and the motor to an authorized Wahl service center or a qualified technician.

For what type of shaver

It is for the Wahl 5 Star Vanish shaver, code 08173-716. Compatibility is confirmed only for the Vanish, so do not buy it for the Finale, Super Close, Mobile Shaver, or for hair clippers. If you are not sure about the defect, first ask for a diagnosis at the service center.

Specifications

What else you need

• The Wahl 5 Star Vanish shaver, for which the part is intended
• Wahl 3022905 replacement foil and blades for Vanish
• Replacement battery for Wahl Vanish

ProBeauty's tip. Most often, the motor fails due to liquids. Wahl warns that excess liquid reaches the motor compartment and shortens its life, so spray the disinfectant only on the foils and wipe off the excess.

Spare parts - Printed circuit board for Wahl 5V trimmer

Jaguar - Charging stand for J-Cut 30 contour trimmer

BaByliss PRO BABZ020000010 is the replacement motor for the BaByliss PRO Caruso hair dryer. It is a service part, not an accessory: it is installed inside the dryer by an authorized service center. You buy it if the technician has told you that your Caruso dryer's motor needs to be replaced.

What it does for you

• It can bring your dryer back to life, if the fault is with the motor and the rest of the appliance is in good condition.
• Repair instead of throwing away: a good salon dryer is often worth repairing.
• You have the part with the brand code, BABZ020000010, which the service center can easily verify.
• You shorten the repair time, if the service center does not have the part in stock.

How to use it at home

1. You do not install it at home. The motor is connected to the dryer's electrical system, and incorrect installation can be dangerous.
2. Unplug the dryer and do not use it again until it is repaired.
3. Note down the exact model and code on the handle or the dryer's label.
4. Check with the service center that BABZ020000010 is the right part for your model.
5. Take the dryer and the motor to an authorized BaByliss PRO service center or to a qualified technician.
6. After repair, clean the filter at the back before the first use.

For what type of appliance

The motor is listed for the BaByliss PRO Caruso dryer. BaByliss PRO has had several dryers with this name, for example Caruso (BAB6510IE) and Caruso HQ (BAB6970IE), and the brand does not publish a compatibility sheet for this code. Do not order it until you confirm the model with the service center or with us.

What else you need

• BaByliss PRO BABD11E Diffuser, compatible with Caruso dryers
• Olivia Garden Ceramic+Ion SpeedXL 45 Round Brush
• Wella EIMI Thermal Image Heat Protection Spray

ProBeauty Tip. Before replacing the motor, ask the service center to also check the cable at the handle's exit. In dryers used daily, faults often occur there.

Wahl Beretto Motor 95368-1016 is the complete replacement motor that the official Wahl parts list specifies for the Beretto ProLithium (4212-0470) clipper. Replace it when the old motor no longer starts or has lost power. The clipper is repairable, not disposable.

What it does for you

• Your clipper is back in action: a new motor, while the housing, battery, and blade remain.
• Complete motor: the Wahl list refers to it as "Motor completo Beretto," meaning the entire motor assembly, not just one of its components.
• The exact model code: 95368-1016 is listed for the Beretto ProLithium, alongside its other parts.
• Simpler servicing: the technician receives the part directly from the Wahl list.

How to use it at home

1. Fully charge the clipper, clean and lubricate the blade: sometimes this solves a slow clipper.
2. If that doesn't help, check the label to make sure you have the Beretto 4212-0470.
3. Take the clipper and motor to an authorized Wahl service center for installation.
4. After repair, test the clipper for a few minutes with a lubricated blade before cutting hair.

For what type of device

For the Wahl Beretto ProLithium (4212-0470) cordless clipper, as specified in the Wahl parts list. We have no confirmation for the Beretto Stealth, as it has a different model code. It is not for the Beret, which has a different motor.

What else you need

• Wahl 97581-2016 Charger for Beret and Beretto
• Wahl Blade Oil
• Wahl Blade Ice Spray for Blades

ProBeauty Tip. Keep the old motor until the repair is finished. If the service center finds another cause, you can return the unopened new part.

Wahl Beret Motor 08723-1716 is the replacement motor that Wahl lists as the official part for the Beret trimmer. Replace it when the old motor has burned out, makes unusual noise, or no longer has power. The rest of the machine remains the same.

What it does for you

• Restore your trimmer without buying a new Beret.
• The exact part: Wahl lists 08723-1716 as the "Beret Motor" for both the silver and black versions.
• Same performance as before: the motor is made for the model, not an adapted part.
• Faster service: the technician receives the part directly from the Wahl list.

How to use it at home

1. Rule out simple causes: clean the blade, apply oil, and fully charge the machine.
2. If the motor still does not work properly, check the model on the label: Beret 08841-616 or 08841-1516.
3. Take the machine and motor to an authorized Wahl service center; Wahl has authorized repair centers in Europe.
4. After installation, oil the blade and test the machine for a few minutes before use.

For what type of device

For Wahl Beret trimmers: the silver model 08841-616 and the black Stealth Beret model 08841-1516, as listed in the Wahl parts list. It is not for the Beretto, Detailer, or Magic Clip, which have different motors in the same list. For an older Beret with a different code, ask us.

What else you need

• Wahl Beret Trimmer
• Wahl Beret Stealth Replacement Blade
• Wahl 97581-2016 Charger for Beret and Beretto
• Wahl Blade Oil
• Wahl Blade Ice Spray for Blades

ProBeauty Tip. Most motors wear out because the blade is unlubricated and clogged with hair. After repair, put a drop of oil on the blade before every trim and clean out the collected hair.

The Wahl Magic Clip and Super Taper Cordless printed circuit board 08591-2030 is the replacement electronic board listed on the official Wahl parts list for the Magic Clip Cordless 08148-016 and Super Taper Cordless. The circuit connects the battery, switch, and motor. When it fails, the clipper will no longer turn on or charge.

What it does for you

• Repair the clipper, don't throw it away: if the rest of the clipper is in good condition, a new circuit will get it working again.
• The same part number for two models: the Wahl parts list lists 08591-2030 for both the Magic Clip Cordless and Super Taper Cordless.
• Genuine Wahl part, with the part number from the brand's parts list.
• Simpler servicing: the technician receives the correct part directly, without searching.

How to use it at home

1. First, check the charger and contacts; a clipper that won't turn on doesn't always have a faulty circuit.
2. Check the clipper's label: the circuit is for the Magic Clip Cordless 08148-016 and Super Taper Cordless.
3. Take the clipper and part to an authorized Wahl service center; Wahl has authorized repair centers in Europe.
4. After installation, fully charge the clipper and oil the blade before the first use.

For which type of device

For Wahl Magic Clip Cordless 08148-016 and Super Taper Cordless clippers, as listed on the Wahl parts list. It is not confirmed for newer generations of the Magic Clip Cordless or for the Senior. It is a service part, not an accessory you swap between clippers.

What else you need

• Wahl Magic Clip Cordless Clipper
• Wahl Super Taper Cordless Clipper
• Wahl Magic Clip Cordless Replacement Blade
• Wahl Blade Oil
• Wahl Blade Ice Spray

ProBeauty Tip. Before spending money on a circuit board, ask the service center for a diagnosis. In cordless clippers, a worn battery shows similar symptoms, and the repair may be different.

The Moser Edition Pro Motor for dryer 0210-7251 is the replacement motor for the Moser Edition Pro professional hair dryer. According to the Moser data sheet, the Edition Pro has a safety thermostat and a removable filter that you can clean. Replace it when the dryer no longer blows, blows weakly, or the motor makes noise.

What it does for you

• The dryer blows powerfully again: the motor is what provides the airflow for fast drying.
• You don't buy another dryer: the housing, heating element, and nozzles remain, if they are in good condition.
• The dryer remains the one you know: the speed and heat settings and the cool air button remain the same.
• Service repair: installation is done with original parts, as required by Moser.

How to use it at home

1. Unplug the dryer and let it cool down.
2. Remove the filter and clean it; a clogged filter suffocates the motor.
3. If the dryer still doesn't work well, take it with the new motor to an authorized service center.
4. After installation, turn it on at the low setting first and listen to see if it runs evenly.

For what type of device

For the Moser Edition Pro hair dryer, type 4330/4331. Moser does not publish the parts list for this dryer, so check the type on the device label before ordering. It is not a part for clippers or other dryers.

What else you need

• Heat protection spray
• Heat protection spray for smoothing
• Round brush for drying

ProBeauty tip. Clean the dryer filter once a week if you use it daily. The air passes freely, the motor does not overheat, and the thermostat does not stop the dryer in the middle of styling.

The Moser Li+Pro Battery with Circuit 1884-7100 is the battery and electronic board assembly for the Moser Li+Pro clipper. The Li+Pro can be used corded or cordless, according to Moser. Replace it when the clipper holds its charge for less and less time or no longer charges.

What it does for you

• Cut cordlessly again: without a good battery, the Li+Pro remains plugged in.
• Order by code: compare 1884-7100 with the code on the old part before installation.
• One-piece battery and circuit: the service center replaces the assembly, not individual parts.
• You can also work corded: until installation, the clipper can be used plugged in.

How to use it at home

1. First, check the stand, power supply, and charging contacts.
2. Take the clipper and part to a service center; Moser requires that batteries be replaced only there.
3. After installation, fully charge the clipper on the stand before the first cut.
4. Clean and lubricate the blade after each use so that the battery lasts as long as possible.

For what type of device

For the Moser Li+Pro clipper, type 1884, the one with the Magic Blade II blade. Code 1884-7100 does not appear in the parts list published by Moser, and for the Li+Pro², the list shows a different battery. Check the type on the clipper's label and the code of the old part before ordering.

What else you need

• Moser Li+Pro 1884-7020 Motor
• Blade oil
• Blade cooling and cleaning spray
• Hairdressing cape

ProBeauty Tip. Moser manuals state that you should not leave the clipper exposed to frost or high heat for long periods. Do not leave it in the car during summer or near a heater.

The Moser Li+Pro Motor 1884-7020 is the replacement motor that Moser's official parts list calls the "1884 Li+Pro motor" and lists for the Li+Pro². According to Moser's data sheet, the Li+Pro has a chip-controlled DC motor with noise reduction, operating at approximately 5200 rpm. Replace it when the clipper no longer starts or loses power while cutting.

What it does for you

• Consistent power again: Moser says that the chip-controlled motor maintains consistent cutting power.
• Keep your clipper: the Magic Blade II blade, battery, and stand can be reused if they are in good condition.
• The correct part number: 1884-7020 is the motor listed in Moser's parts list.
• Work quietly: a new motor no longer makes the noise of a worn-out motor.

How to use it at home

1. Fully charge the clipper and clean the blade; a stuck blade can make a motor seem defective.
2. If it still doesn't work, take the clipper and motor to an authorized service center.
3. After installation, oil the blade and run the clipper for a few minutes.
4. When cutting long hair, take short breaks to let the blade cool down.

For which type of clipper

For Moser Li+Pro (type 1884) and Li+Pro² (type 1888) clippers, according to Moser's designation and parts list. This is not the motor for the Li+Pro Mini, which is a different clipper with a narrower blade. If you don't know the type, check the label on the clipper.

Specifications

What else you need

• Moser Li+Pro 1884-7100 battery with circuit
• Blade oil
• Blade cooling and cleaning spray
• Clipping cape

ProBeauty tip. The Li+Pro has an indicator that shows you when the blade needs to be oiled. Don't ignore it: a dry blade puts extra strain on the motor and wears it out faster.

The Moser ChromStyle Pro Battery 1871-7960 is the replacement battery for the Moser ChromStyle Pro hair clipper. Moser's official parts list specifies it for the black and white ChromStyle Pro and the 1871-0078 set. The manual states that the clipper uses a LiFePO4 lithium-ion battery. Replace it when the clipper's cordless runtime becomes increasingly short.

What it does for you

• Restore full runtime: Moser states that the ChromStyle Pro provides up to 90 minutes of cordless runtime.
• Fast charging: according to the manual, the clipper charges in approximately 60 minutes.
• No memory effect: Moser describes the clipper's lithium batteries as durable and free from memory effect.
• Battery only: Moser's parts list specifies the circuit separately, so you only pay for the worn part.

How to use it at home

1. Clean and lubricate the blade; the manual states that a very dirty and unlubricated blade can cut the runtime in half.
2. If the clipper's runtime is still too short, take it to an authorized service center; Moser requires that batteries be replaced only there.
3. After installation, place the clipper on the stand; overcharging is prevented by the intelligent charging management system.
4. Use it corded via the power supply while the clipper is charging.

For which type of device

For the Moser ChromStyle Pro hair clipper, model 1871: 1871-0071, 1871-0072, and the 1871-0078 set, as specified in Moser's parts list. We cannot confirm compatibility with other ChromStyle clippers, including those sold under the Wahl brand. Send us the code on the label and we will check.

Specifications

What else you need

• Moser 1854-7833 stand and guide
• Blade oil
• Blade cooling and cleaning spray
• Hair clipper cape

ProBeauty tip. The Moser manual states that runtime gradually decreases with daily use, even with batteries designed for professional use. If the clipper has been used intensively for several years, it is normal for it to require a new battery.

The Moser Genio Plus Support and Guide 1854-7833 is a replacement part for the Moser Genio Plus hair clipper. The code 1854 is the Genio Plus clipper type. Moser does not publish a data sheet for this part, so order it when the service center or the code on the old part tells you exactly 1854-7833.

What it does for you

• The clipper is back to work: you only replace the broken or worn part, by its code.
• Order by code, not by picture: compare 1854-7833 directly with the code on the old part.
• Part for the clipper type: the prefix 1854 is the Genio Plus type.
• Minor repair: you don't replace the whole clipper for a small part.

How to use it at home

1. Remove the battery and then the blade, sliding it off the housing.
2. Compare the code and shape of the old part with the new part before installation.
3. If you have never disassembled a clipper, leave the installation to an authorized service center.
4. After installation, snap the blade back into place until it clicks, lubricate it, and turn on the clipper as a test.

For what type of device

For the Moser Genio Plus hair clipper, type 1854, with the detachable Magic Blade blade. For the ChromStyle Pro, which uses the same blade, Moser does not confirm the part. Check the type on the clipper label and the code of the old part before ordering.

What else you need

• Moser Genio Plus Motor 1854-7060
• Moser Genio Plus Battery 1854-7988
• Moser ChromStyle Pro Battery 1871-7960
• Blade oil
• Cooling and cleaning spray for blades

ProBeauty tip. When removing the Genio Plus blade, slide it off the housing as shown in the manual and do not force it sideways. The parts around it will last longer.

The Moser Genio Plus Motor 1854-7060 is the replacement motor for the Moser Genio Plus hair clipper, the one with the removable battery. The official Moser parts list refers to it in the Genio Plus as the "2.6 V 1854 motor". Replace it when the clipper no longer starts with a charged battery or loses power while cutting.

What it does for you

• Cut with power again: The Genio Plus has, according to Moser, a noise-dampened DC motor with approximately 5000 rpm.
• Keep the two-battery system: the clipper comes with two batteries and continues to work with them.
• Part with the correct code: 1854-7060 is the motor in the Genio Plus parts list.
• Repair, not a new device: the Magic Blade blade, batteries, and charging station remain.

How to use it at home

1. First, try the other charged battery; sometimes the battery is worn out, not the motor.
2. Clean and lubricate the blade; a stuck blade strains the motor.
3. If the clipper still does not work, take it with the new motor to an authorized service center.
4. After installation, oil the blade and run the clipper for a few minutes as a test.

For what type of device

For the Moser Genio Plus hair clipper, type 1854, with a removable battery and 46 mm Magic Blade blade. It is not the motor for the Arco pet clipper, which has a different code in the Moser parts list, nor for the standard Genio, type 1565.

Specifications

What else you need

• Moser Genio Plus Battery 1854-7988
• Moser 1854-7833 Holder and Guide
• Blade oil
• Blade cooling and cleaning spray

ProBeauty Tip. Use the batteries one after the other, not just one. The Genio Plus manual is designed around this idea: one works, the other charges. The motor always receives a good voltage.

The Moser ChroMini Battery 1590-7290 is the replacement battery for the Moser ChroMini cordless trimmer. The ChroMini runs only on battery power, so a worn-out battery will cause it to stop working. Replace it when the trimmer holds its charge for less and less time or no longer charges.

What it does for you

• The trimmer works again: The ChroMini runs only on battery power, without a cable.
• Unrushed contouring: no more working with your eyes glued to the little light at the bottom of your beard.
• You keep the small and lightweight trimmer: Moser describes it as very light and quiet.
• Simple repair in the service center: only the battery is replaced, the rest of the trimmer remains.

How to use it at home

1. First, check the stand and charging contacts; clean them of hair with a dry brush.
2. Take the trimmer and battery to a service center; Moser requires that batteries only be replaced there.
3. After installation, fully charge the trimmer on its stand before the first contouring.
4. Clean and lubricate the blade after each use, so the battery lasts as long as possible.

For what type of device

For the Moser ChroMini cordless trimmer (1591-0052 and 1591-0057). The ChroMini Pro has a different battery in Moser's list and a different charging stand. Code 1590-7290 does not appear in the list published by Moser, so check the model on the trimmer's label before ordering.

What else you need

• Moser ChroMini Designer Blade 1590-7350
• Blade oil
• Cooling and cleaning spray for blades

ProBeauty tip. If the trimmer doesn't last long even though the battery is new, check the blade. Moser manuals state that if blade maintenance is neglected, the operating time can decrease significantly.

The Moser Li+Pro Mini Motor 1584-7050 is the replacement motor for the Moser Li+Pro Mini trimmer, type 1584. The code prefix, 1584, is the type for the Li+Pro Mini, Moser's corded or cordless trimmer. Replace it when the trimmer no longer starts, runs intermittently, or sounds much louder.

What it does for you

• Clean outlines again: a trimmer needs a motor that pulls consistently.
• Keep the trimmer you know: Moser describes it as very lightweight and quiet, good for fine work.
• Part for the trimmer type: the 1584 code prefix is the type for the Li+Pro Mini.
• Repair, not a new device: the blade, battery, and stand remain, if they are in good condition.

How to use it at home

1. Fully charge the trimmer and clean the blade; a stuck blade can mimic a faulty motor.
2. If it still doesn't work, take the trimmer and motor to an authorized service center.
3. After installation, put a drop of oil on the blade and run the trimmer for a few minutes.
4. Work with short breaks when cutting long hair, so the blade does not overheat.

For what type of device

For the Moser Li+Pro Mini trimmer, type 1584, with a Star Blade II blade. For the Li+Pro² Mini, Moser's list gives a different motor code. The code 1584-7050 does not appear in the list published by Moser, so check the type on the trimmer's label before ordering.

What else you need

• Blade oil
• Blade cooling and cleaning spray
• Haircutting cape

ProBeauty tip. The Moser manual says that a dirty and unlubricated blade significantly shortens the working time. The same blade also strains your motor. Lubricate it after every trim.

The Moser Genio Battery with Circuit 1565-7880 is the battery and electronic board assembly for the Moser Genio hair clipper. The Genio can be used corded or cordless, and the battery provides its cordless runtime. Replace it when the clipper no longer holds a charge or fails to charge at all.

What it does for you

• Cut hair cordlessly again: without a good battery, the Genio remains tethered to the wall outlet.
• One-piece battery and circuit: the service center replaces the entire assembly rather than searching for separate parts.
• Keep your lightweight clipper: Moser describes the Genio as extra-lightweight, making it worth repairing.
• Still works corded: until it is installed, you can continue working with the power supply plugged in.

How to use it at home

1. First, check the clipper's power supply and charging port; dirt on the contacts can also prevent charging.
2. Take the clipper and part to a service center; Moser requires that batteries be replaced only there.
3. After installation, fully charge the clipper before its first use.
4. Clean and lubricate the blade after each use to prevent unnecessary strain on the motor.

For which type of device

For the Moser Genio hair clipper, model 1565, the one with the Magic Blade. It is not for the Genio Plus, which has a different battery listed by Moser, 1854-7988. Code 1565-7880 does not appear in the parts list published by Moser, so check the model on the clipper's label before ordering.

What else you need

• Blade oil
• Blade cooling and cleaning spray
• Hair clipper cape

ProBeauty tip. Store the clipper at room temperature. Moser manuals state that it should not be exposed to extreme cold or high heat for extended periods. Do not leave it in the car during summer or near a heater.

Moser 1400 Complete Housing 1403-7010 is a replacement housing for the Moser 1400 series corded hair clipper. 1403 is the code Moser uses for the 1400 clipper parts in the official parts list. Replace it when the old housing is broken, cracked, or broken at the mounting points.

What it does for you

• The clipper is securely held again: no cracks and no edges that scratch you.
• The mechanism stays enclosed: hair and dust no longer enter through cracks to the coil.
• You don't replace the whole clipper: the blade, coil, and cable remain, if they are in good condition.
• And the switch is available: the Moser list gives the same switch for the 1400 as for the Primat, 1230-7071.

How to use it at home

1. Unplug the clipper and remove the blade.
2. Take a photo of the inside before moving the parts: coil, vibrator, springs, cable.
3. Move the parts into the new housing, in the same position.
4. Close the housing, mount the blade and lubricate it.
5. Turn the clipper on briefly; if it makes a loud noise, adjust the blade as shown in the manual or take it to a service center.

For what type of device

For the Moser 1400 corded hair clipper. The Moser manual covers types 1170, 1400, and 1411 together, but the parts list gives different housings for the 1400 and the 1400 Mini. Therefore, check the type on the clipper label before ordering.

What else you need

• Moser Primat Switch 1230-7071
• Blade oil
• Cooling and cleaning spray for blades
• Hair clipper cape

ProBeauty Tip. On the 1400 clippers, loud noise after assembly usually comes from the blade or its adjustment. The Moser manual explains the adjustment step by step; follow it before you think the part is to blame.

The Moser Class 50 12 V DC 1250-7070 motor is the replacement motor for the Moser Class 50 corded hair clipper. Moser's official parts list includes it for the Class/Max 50 model, type 1250, and the Class 50 manual specifies a 12 V DC motor. Replace it when the old motor no longer starts, overheats, or loses power.

What it does for you

• Your clipper cuts with power again: a new motor restores the power Moser describes for the Class 50.
• Keep the clipper you know: the Class 50 is made, according to Moser, for continuous professional use.
• The correct part number: 1250-7070 is the motor listed in the model's parts list.
• Repair instead of a new device: the housing, cable, and blade remain the same, provided they are in good condition.

How to use it at home

1. First, check the cable, power supply, and outlet: the Class 50 manual lists them as the primary cause when the clipper does not work.
2. Clean and lubricate the blade; a stuck blade strains the motor.
3. If it still does not work, take the clipper and new motor to an authorized service center.
4. After installation, oil the blade and run the clipper for a few minutes as a test.

For what type of device

For the Moser Class 50 corded hair clipper, type 1250, the one with the 49 mm Star Blade. Moser's list groups it with the Max 50 under the same type. It is not the motor for other Moser models, such as the Class 45, which lists a different motor.

Specifications

What else you need

• Blade oil
• Cooling and cleaning spray for blades
• Hair clipper cape

ProBeauty's tip. Motors fail more often when the blade is dull or unsharpened. Along with the motor, check the blade. If it pulls clean and lubricated hair without tugging, replace it too.

Moser Primat 2in1 Lower Housing 1234-7000 is the bottom part of the housing for the Moser Primat 2in1 corded hair clipper. The code 1234 is the Primat 2in1 type, according to the Moser data sheet and manual. Replace it when the lower housing is cracked or broken at the clips.

What it does for you

• The clipper stays securely in your hand: an intact housing no longer wobbles and has no sharp edges.
• The interior stays clean: hair and dust enter the motor through cracks.
• You don't have to replace the whole clipper: Moser describes the Primat 2in1 as a clipper for continuous professional use.
• Part for your clipper type: the 1234 prefix of the code is the same as your clipper type.

How to use it at home

1. Unplug the clipper and remove the blade.
2. Unscrew the screws and note which parts are in the lower housing.
3. Use the brush to clean the hair collected inside.
4. Move the parts into the new housing in the same position, and close the clipper without forcing the screws.
5. Put the blade back, lubricate it, and turn on the clipper for a test.

For what type of device

For the Moser Primat 2in1 corded hair clipper, type 1234, which comes with a standard blade and a fine one for outlining. Moser does not publish a parts list for this model, so check the type on the clipper label. We have no confirmation for the Primat 1230 or other models.

What else you need

• Moser Primat 1230-7590 Upper Housing
• Moser Primat 1230-7071 Switch
• Moser Primat 1230-7720 Blade Guide
• Moser Primat 1230-7730 Balancer
• Blade oil
• Blade cooling and cleaning spray

ProBeauty Tip. When replacing the housing, also clean the cable contacts at the entry. A cable properly secured in the housing does not break at the bends.

The Moser Primat 1230 Balancer 1230-7730 is a moving part of the motor in the Moser Primat hair clipper. After Moser, the Primat has a polarized oscillating armature motor, approximately 3000 rpm. The balancer is the part that oscillates and moves the blade. You replace it when it is worn, cracked, or when the clipper starts to vibrate irregularly.

What it does for you

• The clipper runs quietly again: Moser describes the Primat as very quiet, and a worn balancer ruins exactly that.
• The blade receives the correct movement: the cut becomes clean again, without pulling.
• Part by Moser code: 1230-7730 is listed as a balancer in the Primat 1230 parts list.
• Don't buy another clipper: the Primat is designed for continuous work and can be repaired part by part.

How to use it at home

1. Unplug the clipper and open the blade and housing.
2. Take a photo of the position of the balancer and the springs before you disassemble anything.
3. Mount the new balancer in exactly the same position.
4. Close the clipper, oil the blade, and run a short test.
5. If the clipper buzzes loudly or overheats, stop and take it to an authorized service center.

For what type of device

For the Moser Primat 1230 corded hair clipper, as listed in the Moser parts list. It is a mechanism part, not a replacement accessory between clippers. For the Primat 2in1 or other models, we do not have confirmation from Moser.

Specifications

What else you need

• Guide for Moser Primat 1230-7720 blade
• Moser Primat 1230-7590 upper housing
• Moser Primat 1230-7071 switch
• Moser Primat 1230-7035 pivot set
• Blade oil
• Cooling and cleaning spray for blades

ProBeauty advice. If the clipper has started to buzz louder, check the blade first. A dirty or un-oiled blade strains the motor and resembles a worn part.

Moser Primat 1230 Switch 1230-7071 is the on/off button for the Moser Primat corded hair clipper. The official Moser parts list specifies it for the Primat 1230 and for the 1170 and 1400 clippers. Replace it when the clipper no longer starts reliably or turns off on its own from the button.

What it does for you

• The clipper starts right away: a new switch no longer has loose contacts.
• You work without interruptions: sudden shutdowns in the middle of cutting disappear.
• One part for three models: the same code is listed for the Primat 1230, the 1170, and the 1400.
• A minor repair, not a new clipper: the rest of the clipper remains the one you know.

How to use it at home

1. First, check the cable and the socket: a clipper that doesn't start doesn't always have a faulty switch.
2. Unplug the clipper and open the housing, with the blade removed.
3. Note down or photograph how the wires are connected to the old switch.
4. Mount the new switch in exactly the same position and close the housing.
5. If you haven't worked with electrical parts before, leave the installation to an authorized service center.

For what type of device

For the Moser Primat 1230 corded clipper and, according to the Moser parts list, for the Moser 1170 and 1400 clippers. It is not a part for cordless clippers. For another model, check the code on the clipper's label before ordering.

Specifications

What else you need

• Moser Primat 1230 Upper Housing 1230-7590
• Moser Primat 2in1 Lower Housing 1234-7000
• Moser Primat 1230 Blade Guide 1230-7720
• Moser Primat 1230 Balancer 1230-7730
• Blade Oil
• Blade Cooling and Cleaning Spray

ProBeauty Tip. Moser manuals state that electrical repairs should only be carried out by specialists using original parts. The switch involves live wires, so a service center is the safe choice.